Kac Para Yarismasi

Arthritis Diet and Exercises

How to Fix Atomizer Short & Check Atomizer Message Issues


– Atomizer short? What does that mean? Isn’t this one of the worst things that you can have while you’re vaping? Yes, yes it is. So, how do you fix it? It’s a lot easier than you might think. Before the walkthrough, make sure that you
subscribe to our channel for more info and fun. Atomizer short, check atomizer. These are both messages that tell you that there is something not quite right. This can happen with either prebuilt coils or rebuildable coils. Both are just as simple to fix. Follow these steps to fix it. And first, checking your mod. To check your mod, you wanna
take the tank off first. Once we have the tank off of your mod, you wanna look at the screen
and press the fire button. If it gives you the exact same message, you might wanna try powering
it off and back on again. It should resolve the problem
and you should be fine. But if it continues to
give you that message, even after you’ve powered
it off and back on, there’s something wrong with your mod. Use that tank on another mod
just to see if it’ll work. And if it does, great. Now, let’s stake a look at your tank. You wanna take it apart,
at least so that you can access the coil and the base individually. Check the base of your tank, specifically the 510 pin. If it’s adjustable, it should have a slot for either a flathead or a
Philips head screwdriver. Should you not see one, you should be able to
push and pull the pin from inside the base to get it connected. Use the appropriate tool and loosen by twisting counterclockwise
once or twice. The reason you wanna do this is because the 510 pin may not
be connecting with the mod. Reinstall the tank,
and if it works, great. But if not, here’s what you do. Take your tank apart so
all you have is the coil. Pull or twist the bottom of the coil, like you would on the 510 pin, to hopefully make that connection. This will make the magic happen. But if it doesn’t, then
it’s a really sad day. You should change the coil out with another one in the pack. These are the steps for fixing a prebuilt coil atomizer short message, but what if you have an RDA? If you’re getting this message with either an RDA or an RTA, here’s what you do to fix that. Expose the rebuildable deck by taking the cap off and
checking the screws first. If they’re not tightened
enough, or they’re too tight, adjust them appropriately
and it should be good to go. Still getting that message? Check the 510 pin. You should be able to adjust the 510 pin on the base of the tank. You’re gonna wanna loosen it so that it connects with the mod. If you’re still getting that
message, check your coils. It’s possible that they’re either connecting with the deck or the side of the casing of the top. Adjust the coils so they’re
not touching the deck or change them out if they’re broken. There you have it! You’re vaping and enjoying the experience. For more information that I
didn’t cover in this video, we a link to a blog
down in the description. You’ll make sure to click on that and share that with your friends too. If you have any tips or questions, make sure you comment down below. We’d love to talk to you. To stay in the know,
make sure you check out the Community tab on our YouTube channel. We’ll see you next time.

100 thoughts on “How to Fix Atomizer Short & Check Atomizer Message Issues

  1. Can we open that bottom base without breaking it. My coil got overheated n stuck in. Can't remove it

  2. Thank you so much. I just bought a brand new voopoo drag 2 and no other coil was working in it, besides the one it came with. You just saved my night, and my wallet. โค

  3. Ty putting in a new coil is always scary and i have thrown out a couple coils in the past that were probably good because of errors. Powering on and off fixed this and yes its a SMOK lol. You guys are great ive ordered from you multiple times. Subbed <3

  4. This was extremely helpful my guy thanks a lot !!!! Was really stressing for about 30 mins ๐Ÿ˜‚๐Ÿ˜ญ๐Ÿ˜ญ๐Ÿ˜ญ๐Ÿ˜ญ

  5. Hi, I have a atomizer short problem on my wisemec luxotic device. I have done everything you have mentioned in the video but the error still persist. Please help

  6. Wow, it actually worked!! Thanks a lot. I really didn't want to throw away a brand new coil. (This was for my Aspire Cleito 120)

  7. Thanks for the help. I was able to resolve my issue within a few minutes after watching the video. Thanks again

  8. Didn't work, broke it, did a smashy smash. It should have tapped out, if it did we could've still been together.

  9. Omg, i don't know what happend but I was looking for my Vaporesso armour pro and while i was I lift my pillow It felt o. The floor and It showed that message, did what you said here and It works! Thank you

  10. I always overkill my check process. I've learned that the non adjustable 510 pins will let you know its hitting the coil by first checking that it floats/moves freely then as you screw the coil in, push in on the 510 pin from the bottom and when the coil hits it, you'll feel it start to be pushed out. Again theres also the mod that might not be hitting the pin for various reasons but you're showing everyone what they can do to fix that. You're vid is one I watched as I started vaping and have to say thank you for all the info and advice you've made available

  11. Thank you so much voopoo drag 2…changed from the smaller coil to bigger coil it came with, the power button trick on n off with tank off still read check atomizer with tank off and reset I thought the worst but pulled the coil bottom piece upwards like suggested boom… fixed!

  12. So i tried different parts and ultimately traced my problem to my batteries. The hatch doesnt close completely, flawed design, so the batteries arent seating properly. After a couple reasonable smacks (to knock the batteries into place) my problem was solved. The mod was probably misreading the issue off my batteries (poor babies)

  13. I checked every step except the one that you test it on a different mod. The thing is that it sais "Shorted" but i can still do puffs when firing it repeatedly.. idk man

  14. I feel like an idiot, I have been vaping for over 7 years, and I still feel like a newbie! So thank you for the help

  15. Man, you are a lifesaver. I just purchased a new tank and I thought it wasnโ€™t compatible with my mod. Thanks a lot

  16. I get Atomizer short, or Atomizer low message, when I screw the tank on too tight. If it's loose it works just fine, what can cause this issue? I tried with several coils and it's the same thing. I use the cuboid mini

  17. Thank you so much!!! I've been using the voopoo drag 2 for months now and just had this issue. Your video saved me from spending an unnecessary amount of time and money ๐Ÿ˜‚

  18. Hi, Im Currently using an "XO DYNAMIC" from Liberty Flights, just got some new coils and changed out the old one for a newer one and now every time i press the button on it, it says "HEAT FAULT" after cycling to 0.4 seconds. Please could you give me some advice on how I can fix this issue as im still new to vaping plus cant really afford a new one as of right now. Any advice and/or info would truly be appreciated so I can get back to vaping. Thank you!

  19. I have a short problem on an Rta and it works fine as long as my battery is full. If the battery falls below 80-90 it sais Shorted sometimes and it gets worse when the battery is low

  20. Just love you mate your trick about loosing my 510 pin connector save me,and 2 mins before i see your video i tighten up ccause i think it the right,ty very much and keep up the good work!!!

  21. Omg thank you so fucking much. Literally saved my dumb ass from just giving up and buying a new one ๐Ÿคฆ๐Ÿฝโ€โ™€๏ธ๐Ÿ˜‚

  22. If I'm squonkin should I loose squonk pin? I have this issue with Pulse 80w, it's gives like half powered hit,then comes the short message and after that mod sometimes "shutdown" & comes back on. I get mod working firing it couple times but mod is still doing that.

  23. This video is the best out there for fixing the "Check Atomizer" message! We followed the video and it took like 30 seconds to fix the issue before the video even finished! Perfect!

  24. please do not advise people who may not know what they are doing to loosen a 510 pin on an RDA or RTA, this can further exacerbate problems and in its self cause a short.

  25. Pull out the coil. Thought that would break it. It doesnt and af6er an hour of cleaning followed by message rage, I can now enjoy a vape again. Cheers man. Expert

  26. Hello vape fam, I currently have my Charon TC 218, and my vape works fine all the time with Kanthal coil. And then I switched to Alien Clapton and I cannot fire my vape and a "shorted" message appear. But when I loose my atomizer a little bit it works. Is it really fine to do this technique?

Leave a Reply

Your email address will not be published. Required fields are marked *